Reply To: Sony Projector Software

Reply To: Sony Projector Software

Home Forums Calibration Discussion By Brand Sony Projector Software Reply To: Sony Projector Software

#16777
Gregg Loewen
Keymaster

Image Director 3 is the much more basic software for only manipulating the gamma.

Welcome to ImageDirector!

Getting Started
This file contains the latest information and technical updates concerning ImageDirector. Read this file before using ImageDirector.

——–
Features
——–

ImageDirector is a software that allows you to adjust projector’s gamma value to your satisfaction from a computer connected to the projector by adjusting the luminance curve of the incoming signal. In addition to just using the gamma value that has been adjusted and preset at the factory, you can also adjust the gamma curve yourself, while keeping the default value, and apply the adjusted value to other projectors. You can then save this adjusted value to your computer.
New in ImageDirector3 is a feature that allows you to adjust the gamma value in more detail by selecting any point on gamma curve.

———————————————-
Operating system environment for ImageDirector
———————————————-

The ImageDirector application can be used in any of the following operating system environments.
Operating systems:
Microsoft
Windows XP Home Edition/Professional Service Pack 3 or later,
Windows Vista Home Basic/Home Premium/Business/Enterprise/Ultimate Service Pack 2 or later,
Windows 7 Home Basic/Home Premium/Professional/Enterprise/Ultimate Service Pack 1 or later
* The 32-bit and 64-bit editions of the Windows Vista and Windows 7 series are supported.
CPU: MMX Pentium 166 MHz or above (Pentium III 1 GHz or above recommended)
Hard disk: 50 MB or above of free space (100 MB or above recommended)
Memory: 64 MB or above (256 MB or above recommended)
Other hardware requirements:
(Connecting to the projector using a USB cable) USB jack as standard equipment, USB cable
(Connecting to the projector using a RS-232C cable) RS-232C serial port, D-sub 9-pin cross (reverse) cable
(Connecting to the projector using a LAN cable) Network/LAN connector, LAN cable
Screen resolution: SVGA (800 x 600 dots) or above, 65536 colors or above

Notes
– ImageDirector will not work on some computers even though they satisfy the above requirements.
– ImageDirector will not work on Macintosh systems.

– Microsoft, Windows, and Windows Vista are registered trademarks of the U.S. Microsoft Corporation in the United States and other countries.
– Pentium is a registered trademark of Intel Corporation.

—————
Contents of downloaded file
—————

The downloaded file contains the following ImageDirector files and folders.

– Id_Inst.exe: A file used to install ImageDirector on a computer
– Help folder: This folder contains files explaining the configuration of the windows and how to operate ImageDirector.
– ReadMe folder: The “ReadMe” file (ReadMe.txt) for ImageDirector.

————————
Installing ImageDirector
————————

To use ImageDirector, you need to install it on your computer. You need to do this before you use ImageDirector for the first time, or whenever you replace the operating system on your computer.
Install ImageDirector as follows.

Notes
– You need to log on using the “administrator” account.

1 Extract the [ImageDirector.zip] compressed file you downloaded.

2 Double-click the [ID_Inst.exe] file located in the extracted folder.

3 Click [Install].
Installation starts automatically and the setup dialog box opens.

4 Proceed with installation following the messages displayed in the setup dialog box.

Notes
– During installation, an electronic “End-user License Agreement” is displayed. It is important that you read the agreement first. Only after you agree with the agreement can you install ImageDirector.
– If you already have a version of ImageDirector installed, quit the existing ImageDirector and uninstall it before you update your ImageDirector. Install the latest ImageDirector only after you have uninstalled the previous ImageDirector.

== To uninstall ImageDirector ==

Uninstall ImageDirector as follows.

Notes
– You cannot reset the projector’s gamma value to the default value without using ImageDirector. If you have adjusted the projector’s gamma value using ImageDirector, and you want to uninstall the ImageDirector application, reset the projector’s gamma value to the default value before you uninstall it. However, if you want to maintain the adjusted value, you do not need to reset it.
– To uninstall the ImageDirector application installed on your computer, first close down ImageDirector.

For Windows XP, Windows Vista

1 Click [Start] on the taskbar.
The [Start] menu appears.

2 Click [Control Panel] on the [Start] menu.
The “Control Panel” window appears.

3 Double-click [Add or Remove Programs] (for Windows Vista:[Uninstall a Program]).
The “Add or Remove Programs” dialog box (for Windows Vista:[The Programs and Features control panel]) appears.

4 Select “ImageDirector3” from the list, then click [Remove] (for Windows Vista:[Uninstall]).
Uninstallation of ImageDirector starts. Follow the instructions on the screen.

For Windows 7

1 Click [Start] on the taskbar.
The [Start] menu appears.

2 Click [Control Panel] on the [Start] menu.
The “Control Panel” window appears.

3 Click [Uninstall a program] under [Programs].
The [Uninstall or change a program] dialog box appears.

4 Select “ImageDirector3” from the list, then click [Uninstall].
Uninstallation of ImageDirector starts. Follow the instructions on the screen.

——————————————————
While having transmitted and received the gamma value
——————————————————
Please do not operate a projector during communication with a computer. This may cause the gamma value stored in the projector to be corrupted.

Copyright 2002, 2003, 2005, 2007, 2012 Sony Corporation

A-EHV-100-11(1)

  • This reply was modified 3 years, 8 months ago by Gregg Loewen.
  • This reply was modified 3 years, 8 months ago by Gregg Loewen.
Attachments:
You must be logged in to view attached files.